The gas flame is used to raise the temperature and produce heat with the help of gases. The metal is heated up to melting the metal and on cooling it solidify. Filler metal is used for fill the gap of welding and preparation the edges of joints. Many combinations of gases are used in gas welding but commonly used is Oxygen and acetylene.

Oxy-Acetylene welding

The process of oxy-acetylene welding can be used for all .types of metal which is used for engineering purpose. Oxy-Acetylene welding can produce 3200-degree Celsius. These are two systems of oxygen acetylene welding

High pressure system

In this process, the oxygen and acetlyene are taken for use from a high pressure cylinder.

Low pressure system

In this system, oxygen is filled in a high-pressure cylinder and the acetylene is produced by the addition of calcium carbide and water.

CaC2  + 2 H2 O = Ca (OH)2 + C2 H2


Principle of Oxy-acetlyene welding

When the gases began burning the flame is produced through the torch tip. The edge to be welded are heated upto melting. Filler metal is also added to complete the welding. This molten metal mixture when soldify on cooling forms a welding joint.

 Apparatus

Oxygen cylinder

Acetylene cylinder 

Pressure gauges 

Valve 

Hosepipe 

Torch 

Welding tips

Pressure regulators 

Lighter Goggles.

The cylinder filled with oxygen and acetylene. Both the cylinders are attached with pressure gauge, regulator and cylinder valves. The cylinder containing oxygen is painted black where the acetylene cylinder is painted Maroon. Hose pipe are provided with each cylinder. These pipes are connected to the welding torch.

Welding process

To start welding the acetylene control valve is turned first when acetylene comes out of the nozzles it should be ignited with the spark lighter. It will give a yellow coloured smoke flame after it oxygen cylinder valve is opened and supplied is increased until the best suitable flame is obtained. Then the flame is foucussed on the edges to be welded flux and filler matel are also added with the help of heat of frame, the edges and filler metal metals and a joint is performed after cooling of the molten metals. The joint may be formed with or without using filler metals.

 Applications

Same equipment may be used for cutting purpose . Oxy-acetylene welding is particular is used for sheet metal works.

 Types of gas flames

 Oxidising flame

When the volume of oxygen is more than the volume of the acetlyene mixer into the torch. This types of flame are used for cutting the metal and welding the brass metal.

Carburising flames

When the volume of acetylene mixed in more than oxygen carburizing frame is formed. This flame is used to welding nickel, monel

 Neutral flame

It is known as balancing flame oxygen and acetylene gases are mixed in equal volume. This types of flame used for welding steel and cast iron.

 Flux

The chemical which deoxidise the metal surface and provide an inert atmosphere around the molten metal is known as flux. The function of flux
  • To prevent oxide from the hot surfaces
  • To reduce the viscosity of molten metals
  •  It contains a study Arc in the case of arc welding.

Flux is available in liquid, powder, paste, and gas. Powder flux is sprinkling on the surface to be welded or the filler rod is dipped into the Powder liquid and paste flux are sprayed on the surface to be welded. Gas fluxes are used to form in the inert atmosphere around the joint to be welded.

Filler metal

The rod which provide additional metal in completing the welding is known as filler metal. The composition of filler metal should be same as metals to be welded

Similar Posts

16 Comments

  1. Thanks for sharing such an awesome news about gas welding. This post helps me to gather some additional information about gas welding. Keep going! If you are in need of Welding & Cutting Equipment reach brothers gas.

  2. Greetings……
    i will be take examination this coming October… i need more elements specially in Machine Design.. what are the best book and author should be…
    i appreciate for all your help……. thank you for your blog site so helpful.. Good luck to all of us..
    piping design course in chennai

    bim course In chennai

  3. Insanely comprehensive ๐Ÿ™‚

    Thank you so much,
    Now I have something to read during the holidays. This will take a while but well worth it like always
    You can read another one here Besttoolsbrand

  4. really explains everything in detail,the article is very interesting and effective.Thank you. we also provides best service to oxygen cylinder on rent. if you want more information so you can visit on our website.

  5. Thanks for sharing the valuable information. Your article gave me a lot of information.I have gained great information from your post.
    This site is a very good site. I am sure that you will benefit from this web site.
    Whatever you are looking for can be helpful.ย Click Here

  6. I work in a construction industry where I need to do welding every day to combined metal parts together. I use the MIG 211 welding machine and I'm very satisfied with it. If you also try this welding machine for any type of welding you need. Highly recommended!

Leave a Reply

Your email address will not be published.